Abstract: Phenolic resin has long been used as matrix for composites mainly because of its flame retardant behavior and high char yield after pyrolysis, which results in a self supporting structure. The addition of ceramic powders, such as SiC and B4C, as fillers to the phenolic resin, results in better thermo-oxidative stability, but as drawbacks, it has poor homogeneity, adhesion and processing difficulties during molding of the composites. The addition of single elements, such as boron, silicon and phosphorus in the main backbone of the thermo-set resin is a new strategy to obtain special high performance resins, which results in higher mechanical properties, avoiding the drawbacks of simply adding fillers, which results in enhanced thermo-oxidative stability compared to conventional phenol-formaldehyde resins. Therefore, the product can have several applications, including the use as ablative thermal protection for thermo-structural composites. This work describes the preparation of a boron-modified phenolic resin (BPR) using salicyl alcohol and boric acid. The reaction was performed in refluxing toluene for a period of four hours, which produced a very high viscosity amber resin in 90% yield.The final structure of the compound, the boric acid double, substituted at the hydroxyl group of the aromatic ring, was determined with the help of the Infrared Spectroscopy, 1H-NMR, TGA-DSC and boron elemental analysis. The absorption band of the group B-O at 1349 cm-1 can be visualized at the FT-IR spectrum. 1H-NMR spectra showed peaks at 4.97-5.04 ppm and 3.60-3.90 ppm assigned to belong to CH2OH groups from the alcohol. The elemental analysis was also performed for boron determination.The product has also been tested in carbon and silicon fibers composite for the use in thermal structure. The results of the tests showed composites with superior mechanical properties when compared with the conventional phenolic resin.

Abstract: The search for a smokeless propellant has encouraged scientists and engineers to look for a chlorine-free oxidizer as a substitute for AP (ammonium perchlorate). Endeavors seemed to come to an end when ADN (ammonium dinitramide) appeared in the West in the early 1990s. Although some drawbacks soon became apparent by that time, the foremost obstacle for its use in rocket-motors came from the patent originally applied for in the United States in 1990. Furthermore, environmental concerns have also increased during these two decades. Ammonium perchlorate is believed to cause thyroid cancer by contaminating soil and water. In addition, AP produces hydrogen chloride during burning which can cause acid rain and ozone layer depletion. Unlike AP, ADN stands for both smokeless and green propellant. Since then, much progress has been made in its development in synthesis, re-shaping, microencapsulation and solid propellant. The high solubility of ADN in water has also allowed its application as liquid monopropellant. Tests have revealed Isp (specific impulse) superior to that normally observed with hydrazine, one of the most harmful and hazardous liquid propellants. With constraints of use, along with the patent near to expiry, scientists and engineers are rushing to complete developments and patents until then.

Abstract: Synthesis and characterization of energetic ABA-type thermoplastic elastomers for propellant formulations has been carried out. Following the working plan elaborated, the synthesis and characterization of Poly 3-bromomethyl-3-methyl oxetane (PolyBrMMO), Poly 3- azidomethyl-3-methyl oxetane (PolyAMMO), Poly 3,3-bis-azidomethyl oxetane (PolyBAMO) and Copolymer PolyBAMO/AMMO (by TDI end capping) has been successfully performed. The thermoplastic elastomers (TPEs) were synthesized using the chain elongation process PolyAMMO, GAP and PolyBAMO by diisocyanates. In this method 2.4-toluene diisocyanate (TDI) is used to link block A (hardandmono-functional)) to B (soft and di-functional). For the hard A-block we used PolyBAMO and for the soft B-block we used PolyAMMO or GAP. This is ajoint project set up, someyears ago, between the Chemistry Division of the Institute of Aeronautics and Space (IAE) - subordinated to the Brazilian Ministry of Defense - and the Fraunhofer Institut Chemische Technologie (ICT), in Germany. The products were characterized by different techniques as IR- and (1H, 13C) NMR spectroscopies, elemental and thermal analyses. New methodologies based on FT-IR analysis have been developed as an alternative for the determination of the molecular weight and CHNO content of the energetic polymers.

Resumo: Um novo método de análise por via úmida e instrumental foi desenvolvido para avaliação da abertura do anel aziridínico do óxido de tris(l-(2-metil)aziridinil) fosfina (MAPO), agente de ligação usado em propelente compósito. Foi observada redução de intensidade das bandas de absorção em 1400 e 1040 cm-1, que são características do anel aziridínico. Em alguns casos, observou-se que, quando o número de anéis abertos aumenta, a banda de absorção do grupo NH, na região 3400 e 3300 cm-1, que aparece com a abertura do anel, está localizada na região de menor número de onda. O estudo de síntese do derivado do MAPO evidenciou reações secundárias com a hidroxila do ácido 12-hidroxiesteárico, homopolimerização e reação com a umidade existente na amostra.

Abstract: A new method using wet chemistry and instrumental analysis has been developed for evaluating the ring-opening of aziridine tris [l-(2 methyl) aziridinyl] phosphide oxide (MAPO) of the bonding agent used in composite propellant. A reduction was observed in the intensity absorption bands in 1400 and 1040 cm-1, characteristic of aziridinic ring. It was also observed, in some cases, that when the number of open aziridinyl ring increases, the NH band in the range 3400-3300 cm-1, that appears with ring-opening, is located in the region of lower wave numbers. The study of the synthesis of MAPO derivative indicated side reactions such as homopolymerization of rings and also, with secondary hydroxyl of the 12-hydroxy stearic acid and probable humidity existent in the original sample.

No presente trabalho duas técnicas de manufatura de compósitos termoplásticos estruturais são investigadas: a de moldagem por compressão a quente convencional e a de pré-impregnação via suspensão polimérica. A primeira consiste na impregnação do reforço via polímero fundido; enquanto que a segunda faz uso de suspensões poliméricas aquosas, onde a impregnação do reforço ocorre pelo contato deste com a suspensão aquosa de partículas da matriz polimérica. Esta técnica combina a matriz polimérica em pó com um outro polímero formador da suspensão, um poli(ácido âmico - PAA), sendo que os dois polímeros são simultaneamente depositados sobre o reforço, durante a impregnação. Este mesmo PAA, em uma segunda fase do processo, é convertido termicamente em uma poliimida (PI) podendo formar uma região de interfase entre o reforço e a matriz polimérica. Este trabalho tem como objetivo a síntese e a caracterização de um PAA, à base de BTDA/DDS, e a avaliação de sua influência na formação da região de interfase em compósitos de poli(sulfeto de fenileno) (PPS)/fibras de carbono. Resultados de DSC e TG mostram o sucesso da síntese do PAA e de sua conversão em PI, esta com estabilidade térmica até 396 °C. O compósito processado pela técnica de suspensão polimérica apresenta resistência ao cisalhamento interlaminar (56,3 MPa) 12,6% superior ao compósito obtido por moldagem por compressão a quente convencional (50,0 MPa). Estes resultados são confirmados por análises das superfícies de fratura, que mostram que o uso do PAA melhora a interfase do PPS/fibra de carbono.

In the present work two different manufacturing techniques of thermoplastic composites are investigated: the conventional hot compression molding and the aqueous suspension prepregging. The first one involves the impregnation of the reinforcement with molten polymer; while the second one uses aqueous polymeric suspensions, where the reinforcement impregnation occurs by its contact with the particle aqueous suspension of a polymeric matrix. This technique combines the powder polymeric matrix with another polymer which forms the suspension, a poly(amic acid - PAA). In this technique, both polymers are deposited simultaneously on the reinforcement during the impregnation. In a second phase of the processing, the PAA is thermally converted in a polyimide (PI) that can form an interphase region between the reinforcement and the polymer matrix. The objective of this study is the synthesis and the characterization of a PAA, based on BTDA/DDS, and the evaluation of its influence on the interphase region in the poly(phenilene sulphite) (PPS)/carbon fiber composite. DSC and TG results show the success of the PAA synthesis and its conversion into PI, which exhibits thermal stability up to 396 °C. The processed composite by polymeric aqueous suspension showed interlaminar shear strength (56.3 MPa) 12.6% higher than the composite obtained by conventional hot compression molding (50.0 MPa). Fracture surface analyses confirm these results, showing that the use of PAA improves the PPS/carbon fiber interphase.

Azide polymers samples were analyzed by FT-MIR in order to develop a quantitative methodology to determine the C, H and N content in energetic polymers used in propellants. The elemental analysis data were used as reference. The FT-MIR results show a good agreement with CHN analysis. A good linear relationship was obtained suggesting that the methodology developed in the CTA laboratory can be used for quality control of these energetic polymers.

Um método SEC com dupla detecção para determinação de distribuição de funcionalidade de resina polibutadiênica hidroxilada HTPB foi desenvolvido, verificando-se a influência desse parâmetro no comportamento mecânico de poliuretano utilizado em motor-foguete fabricado no Centro Técnico Aeroespacial (CTA). O método mostrou-se sensível a pequenas diferenças de funcionalidade e sua distribuição podendo ser utilizado para a caracterização mais completa da resina. Ensaios de tração realizados em amostras de PU sem carga refletiram pequenas diferenças de distribuição de funcionalidade existentes entre os lotes de polibutadieno hidroxilado.

A size exclusion chromatography (SEC) method, with double detection, was developed to determine the functionality distribution of hydroxyl polybutadiene (HTPB) resin, evaluating the influence of that parameter on the mechanical behavior of HTPB polyurethane used as binder in the rocket motors manufactured at Centro Técnico Aeroespacial (CTA). The method showed to be sensitive to small differences in the functionality distribution of the HTPB resin and, thus, can be used for a more complete characterization of the resin. Tensile tests performed on HTPB polyurethane reflected the small differences observed in the functionality distribution of three batches of HTPB.

O objetivo do presente trabalho é apresentar a síntese de um poli (ácido âmico) (PAA) a ser utilizado como formador de interfase no processamento de compósitos termoplásticos de alto desempenho. Os materiais compósitos termoplásticos constituídos de um reforço rígido e de uma matriz dúctil têm as suas propriedades mecânicas fortemente dependentes do mecanismo de transferência de carga fibra/matriz. Por esse motivo, a região da interface/interfase nos materiais compósitos possui um papel fundamental nas propriedades finais do material. O PAA surge como uma alternativa para melhorar a adesão fibra/matriz na região interfacial em compósitos de alto desempenho, constituídos de matrizes termoplásticas, reforçadas com fibras de carbono ou vidro. O PAA é utilizado na forma de sal, na preparação de suspensões poliméricas de matrizes termoplásticas. O PAA estudado neste trabalho foi sintetizado utilizando-se os reagentes BTDA e DHPr. Em seguida, o PAA foi convertido em PI por imidização em solução. Análises por FTIR mostram o sucesso da síntese do PAA e da sua conversão em PI. As técnicas de DSC e TGA determinaram as temperaturas de transição vítrea (~213 °C) e de decomposição (~310 °C), respectivamente. Estes resultados motivam a utilização do PAA/PI como formador de interfase na obtenção de compósitos termoplásticos com temperaturas de processamento abaixo de 310 °C.

This work is aimed at presenting the synthesis of a poly (amic acid) (PAA) to be used as interphase precursor in the manufacturing of high performance thermoplastic composites. Thermoplastic composites comprising a rigid reinforcement and a ductile matrix have their mechanical properties strongly dependent on the load transfer mechanism between the reinforcement and matrix. For this reason, the interface/interphase region plays a fundamental hole in the final properties of the composite materials. PAA appeared as an alternative to improve the fiber/matrix adhesion when it is transformed in polyimide (PI) favoring the link between the reinforcement and the thermoplastic matrix. This work shows the PAA synthesis from BTDA and DHPr reagents and its conversion into PI by imidization in a liquid medium. Mass spectrometry analysis confirmed the synthesis of PAA from the precursor reagents and the FTIR analysis evaluated the success of the conversion of PAA into PI. DSC and TGA analysis of the PI determined their glass transition (~213 °C) and decomposition (~310 °C) temperatures, respectively. These results motivate the use of PAA/PI as precursor of interphase to obtain thermoplastic composites with processing temperatures below 310 °C.

A rapid, expedient and enantioselective method for the synthesis of beta-hydroxy amines and monosubstituted aziridines in up to 99% e.e., via asymmetric transfer hydrogenation of a-amino ketones and cyclisation through treatment with tosyl chloride and base, is described. (1R,2R)-N-(para-toluenesulfonyl)-1,2-ethylenediamine with formic acid has been utilised as a ligand for the Ruthenium (II) catalysed enantioselective transfer hydrogenation of the ketones.The chiral 2-methyl aziridine, which is a potentially more efficient bonding agent for Rocket Solid Propellant has been successfully achieved.